TBM implantation in CLEX 1 TaskDurationDate 1Remove the safety barriers0.5 days1.06 2Preparation of the storage tables inside CLEX0.5 days1.06 3Radioprotection.

Présentation au sujet: "TBM implantation in CLEX 1 TaskDurationDate 1Remove the safety barriers0.5 days1.06 2Preparation of the storage tables inside CLEX0.5 days1.06 3Radioprotection."— Transcription de la présentation:

1 TBM implantation in CLEX 1 TaskDurationDate 1Remove the safety barriers0.5 days1.06 2Preparation of the storage tables inside CLEX0.5 days1.06 3Radioprotection Survey Visit1 day2.06 4Dismantling of the shielding blocks (to get the direct access for new equipment) 1 day2.06 5Organizing of free access to CLEX building1day3.06 6Initial measurement of the CLEX2days storage

2 SURVEY 5-6Initial measurement of the CLEX : Measurement of the existing references Determination of the theoretical beam 2days Action préalable Discussion préalable à avoir avec Tobias Analyser les résultats des dernières mesures effectuées par le contrat Mesure Mesurer l’ensemble des fiducielles du réseau Mesurer les fiducielles des composants +Re-fiducialisation des composants (Wilfried)  plusieurs jours Action post-mesure Analyse Préparation du plan d’implantation des plaques metrologiques Préparation du plan d’implantation des plaques actionneurs

3 TBM implantation in CLEX 3 TaskDurationDate 6Dismantling of TBTS PB and DB tanks -disconnection of electrical cables and water pipes -disconnection and dismantling of RF network 6.5 days02.06 10.06

4 TBM implantation in CLEX 4 TaskDurationDate 7-dismantling and transport of the TBTS PB Tank to the buffer zone1 day09.06

5 TBM implantation in CLEX 5 TaskDurationDate 8-dismantling and transport of the TBTS DB Tank and transport to the storage 1 day10.06

6 TBM implantation in CLEX TaskDurationDate 9-Disconnection of all cables (+ labelling) and pipes in the working area 4.5 days11.06 17.06 ~ 14 meters

7 TBM implantation in CLEX TaskDurationDate 10-Removal of the equipment in the working area4 days12.06 18.06 ComponentPicQuantityComponentPicQuantity Quadrupoles12Supports10 Correctors10 Sector vacuum valves 4 BPMs and diagnostics chambers 8 Pumping ports (including valves and pumps) 5 Flashbox1 Drift Tubes and bellows 20 + 22

8 TBM implantation in CLEX TaskDurationDate 11-Dismantling of the yellow girders and feet3 days18.06 23.06 12-Removal of the cooling distribution (central line)3 days23.06 26.06 13-Precise Floor marking before drilling of the holes for installation of the TBM supporting system: 32 holes in total For dimensions: DRAWING CLIATCIN0004 1.5 days26.06 27.06 14Drilling of the floor for all the supporting equipment1.5 days30.06 01.07 TaskQuantity Feet to be removed from area6 Feet to be replaced2 Girders to be removed from area6 Girders to be replaced6 New girders to be manufactured (see on next slides) 3 1 day

9 SURVEY 13-Precise Floor marking before drilling of the holes for installation of the TBM supporting system: 32 holes in total For dimensions: DRAWING CLIATCIN0004 1 day26.06 27.06 Action préalable Avoir fini et validé le plan d’implantation Mesure Implantation des 32 trous Action post-mesure Ø

10 Supporting Elements for TBM and CLEX Components 2 Feet to be reused in different place (8 holes to be drilled) New girders (x3) TBM supporting benches (24 holes to be drilled for installation) All green feet will not be moved Green girders will be moved by several cm.

11 TBM implantation in CLEX TaskDurationDate 15-VACATIONS period time reservation30 days01.07 31.07 16-Installation of the supporting elements of the TBM and CLEX components  Installation of the new yellow supporting girders (1 day)  Transport and Installation of the TBM extremity benches (1 day)  Geometrical control of the extremity benches (3 days) 5 days01.08 07.08 17-TBM installation and assembly See next slides 26 days08.08 12.09 1 day 3 days

12 SURVEY 16-Installation of the supporting elements of the TBM and CLEX components  Installation of the new yellow supporting girders (1 day)  Transport and Installation of the TBM extremity benches (1 day)  Geometrical control of the extremity benches (1 day) 3 days01.08 07.08 Action préalable Avoir mesuré les plaques métrologique en métrologie Avoir un plan d’implantation pour les plaques métrologiques Mesure Nivelement et ajustement des plaques métrologiques Controle des mesures CMM des plaques métrologiques Action post-mesure Ø

13 Installation of the TBM supporting system TaskDurationDate 18Installation of the TBM supporting system 5 days08.08-14.08 19Geometrical control of the TBM supporting system 3 days15.08-19.08 20Alignment of the girders (with respect to the existing beam) 1 day20.08 21Installation of alignment’s device (wire, cable, sensors, data acquisition, …) 2 days21.08-22.08 22Absolute measurement (cWPS sensors vs AT401 tracker) 1 day25.08 23Test of actuators displacement on 1 mm range (girder unloaded) 1 day26.08 24Test of the Articulation Point (girder unloaded) 1 day27.08 1 day Tests sous réserve

14 SURVEY 18Installation of the TBM supporting system 5 days08.08-14.08 Action préalable Avoir un plan d’implantation pour les plaques actionneurs Software des actionneurs opérationnel Shelter prêt Mesure Installation des câbles actionneurs Nivelement et ajustement des plaques actionneurs Réglage des actionneurs à mi-course Action post-mesure Ø

15 SURVEY 19Geometrical control of the TBM supporting system 1 day 15.08- 19.08 Action préalable Installer des poids sur la poutre Mesure Mesure de l’ensemble des fiducielles 1.5’’ de la poutre et des berceaux) Action post-mesure Valider l’assemblage poutre-berceau

16 SURVEY 20Alignment of the girders (with respect to the existing beam) 1 day20.08 Action préalable Avoir une position exacte du faisceau existant (dans le réseau général) Mesure Alignement de l’axe des V. par rapport aux faisceaux existants. Action post-mesure Ø

17 SURVEY 21Installation of alignment’s device (wire, cable, sensors, data acquisition, …) 2 days 21.08- 22.08 Action préalable Avoir 20 capteurs calibrés (avec une plaque amagnetique) Protection du fil et du poids prêt Mesure Installation des câbles MCA-8 Installation des câbles Mul-Rad Installation des 4 fils (mise à la masse) Installation de la protection du fil et du poids Action post-mesure Ø

18 SURVEY 22Absolute measurement (cWPS sensors vs AT401 tracker) 1 day25.08 Action préalable Software Acquisition opérationnel Software Calcul absolu opérationnel Mesure Répétabilité des capteurs Test de linéarité Action post-mesure Calcul absolu (comparaison AT401-cWPS)

19 SURVEY 23Test of actuators displacement on 1 mm range (girder loaded with weight) 1 day26.08 24Test of the Articulation Point (girder loaded with weight) 1 day27.08 Action préalable Ø Mesure Mesure AT401 initiale Déplacement de chaque actionneur individuelement (+/-1mm) Déplacement des degrés de liberté Mesure AT401 finale Action post-mesure Analyse Test prévu seulement si les tests dans le lab. sont mauvais En fonction de la stratégie de transport

20 Installation of the components of the TBM + alignment control TaskDurationDate 25Installation of the components of the TBM + alignment control + cooling test5 days28.08-03.09 26Cables for TBM routing and connection to the equipment in the external shelter2 days04.09-05.09 27Test of actuators displacement on 1 mm range (girder loaded)1 day08.09 28Test of the Articulation Point (girder loaded)1 day09.09 29Scanner 3D of the module3 days10.09-12.09 A la fin Tests décalés plus tard (après RFN)

21 SURVEY 25Installation of the components of the TBM + alignment control + cooling test5 days 28.08- 03.09 Action préalable Composants mesurés en métrologie (fiducialiser) Support DBQ opérationnel Mesure Installation des composants à la place des poids Ajustement du DBQ Controle des mesures CMM des composants Mesure de la position des composants sur la poutre Action post-mesure Ø

22 TBM implantation in CLEX TaskDurationDate 30Primary RF Network installation Installation of the RF components on the TBTS tank (2 days) Installation of the waveguides between TBTS tank and TBM Including supports, pumping port etc. (1 day) 3 days28.08 01.09 Test of actuators displacement on 1 mm range (girder loaded)1 day08.09 Test of the Articulation Point (girder loaded)1 day09.09

23 SURVEY 31Test of actuators displacement on 1 mm range (girder loaded)1 day08.09 32Test of the Articulation Point (girder loaded)1 day09.09 Action préalable Après l’installation des RF Network Mesure Mesure AT401 initiale Déplacement de chaque actionneur individuellement (+/-1mm) Déplacement des degrés de liberté Mesure AT401 finale Action post-mesure Analyse Test prévu seulement si les tests dans le lab. sont mauvais

24 TBM implantation in CLEX TaskDurationDate 31 Installation of CLEX components according to new configuration (not all the components are listed below, +5..10 components, final inventory under way) 12.5 days04.08 20.08 ComponentPicQuantityComponentPicQuantity Quadrupoles12Supports18 Correctors8 Sector vacuum valves 4 BPMs and diagnostics chambers 9 Pumping ports (including valves and pumps) 5 Flashbox1 Drift Tubes and bellows 24 + 26

25 SURVEY Action préalable Récuperer les fichiers de fiducialisation des composants Mesure Installation des composants Nivelement et ajustement des composants Action post-mesure Ø Test prévu seulement si les tests dans le lab. sont mauvais 31 Installation of CLEX components according to new configuration (not all the components are listed below, +5..10 components, final inventory under way) 12.5 days04.08 20.08

26 CLEX working area after installation of components

27 Final tests and cables reconnection TaskDurationDate Leaktightness test2 days15.09-16.09 Final alignment tests3 days17.09-19.09 Reconstruction of cable trays and cables pulling5 days17.09-23.09 Reconnection of all cables (according to labelling) and pipes in the working area 2 days24.09-25.09 Cooling system test2 days26.09-29.09 Closing the shielding1 day15.09 Safety chain test1 day30.09 Commissioning5 days01.10-07.10 4 days

28 SURVEY Action préalable Ø Mesure Mesure AT401 initiale Déplacement de chaque actionneur individuelement (+/-1mm) Déplacement des degrés de liberté Mesure AT401 finale Scanner 3D of the module Action post-mesure Ø Final alignment tests4 days 17.09- 19.09